Posts Tagged ‘Marshall’

Orange Amplification Announces DIVO VT1000 Valve Tester

Thursday, January 31st, 2013

Orange Amplification has released the DIVO  VT1000 Valve Tester, an automatic valve tester that performs a host of diagnostics on both preamp and power amp tubes. The unit has one octal and two nine pin valve sockets to fit pe-amp and EL34 valves. Once inserted, the user presses the start button and the tests are run.

Vt1000 valve tester

VT1000 Details:

Tests run:

  • Heater filament test: Short circuit
  • Heater filament test: Open circuit
  • Heater filament test: Tolerance check
  • Heater cathode insulation: Leakage
  • Heater cathode insulation: Short Circuit
  • Tests for heater current abnormalities
  • Amplification factor
  • Voltage gain
  • Power gain
  • Screen grid test
  • Mutual conductance test
  • Dual test for double triodes
  • Emission
  • Inter electrode leakage
  • Inter electrode short circuit
  • Flash-over (arc detection, high voltage breakdown)
  • Gas ionisation test

Compatible Valves:

  • EL34/6CA7
  • EL34L
  • 6L6
  • 6V6/6v6GTA
  • KT66
  • KT77
  • KT88
  • 6550
  • 5881
  • EL84/6BQ5
  • ECC81/12AT7
  • ECC82/12AU7
  • ECC83/12AX7
  • ECC99
  • 12BH7

Does Plate Dissipation Affect Valve / Tube Life In Practice ??

Thursday, November 8th, 2012

In general, the obvious connection between higher anode dissipation and shorter tube life holds good, however,  many other factors affect tube life, including accuracy of heater voltages and the efficiency of tube cooling within amplifiers.

The tube leaves the factory with a known amount of cathode coating material which is the source of all the electron emission. In use, this material is used up as it emits electrons when heated by the filament and plate current is drawn.

If plate current is drawn before the cathode is at operating temperature, the surface of the cathode can be damaged (so called ‘cathode stripping’).

This is why the Standby switch should be off when the amplifier is warming up. If, however, the tube is operated for long periods with the filament hot with little or no plate current being drawn, then an oxide-like coating can form on the cathode, effectively blocking the emission of electrons even when normal operation is required (known as ‘cathode poisoning’). TubeSync takes care of this by automatically controlling the bias at both start-up and run conditions.

vacuum tube EL34 valve

Plate dissipation is generally quoted by the manufacturer as a maximum value which, if exceeded could cause damage to the tube and should not generally be used for ‘normal’ operation. The relationship between tube life and plate dissipation follows an exponential curve. Tubes operated correctly at around 30% maximum dissipation can have lives in the region of tens of thousands of hours and can last several decades of years. This figure decreases rapidly as the dissipation increases, in some cased down to hundreds or even tens of hours as they approach or exceed their maximum plate dissipation rating.

Cooling is extremely important as running tubes very hot also increases the risk of arcing and a condition known as thermal runaway, which can instantly destroy the cathode material, making the tube useless. Conventionally biased tubes are most at risk when biased towards ‘Class-A’ operation, as they experience maximum power dissipation when no audio signal is present.

TubeSync_225

Marshall JVM210 100W & 50W With TubeSync DIVO OV4 Installed

Friday, July 13th, 2012

What is my opinion about the TubeSync Divo OV4? (Charlotte Mijnders – http://www.charlottemijnders.nl )

Well, it has improved my sound, it is much tighter than before, on both the amps it looks like the tubes are matched much better and are pushed to their best performance.

The overall sound is more defined, tighter, more dynamic to my opinion.

On my Jvm210 I have 2 El34’s and 2 6550’s , I can switch between them and they sound as mentioned above, but the best thing is combining all the tubes together, that makes a great sound, more tight bass and bass/mid response of the 6550,and beautiful mids and mid/highs of the El34 on top of it, I like it!.

That is a great option of the Divo, that you can combine tubes in this way.

Pictures

011_02

010_02

divo25_02

015_02

TubeSync Fitted To A Mesa Boogie F-50

Thursday, June 9th, 2011

Sensational blues guitarist Mitch Laddie has been out touring with the product fitted to his Mesa/Boogie F-50, which he said sounds “incredible”. “I had totally fallen out of love with this particular amp before Tubesync was fitted but the difference in sound is more than substantial.The response and tone have been improved ten-fold. Very tight, very fat and all round punchier, especially in the low to mid frequencies.”

Mitch & His Mesa F50“I believe the product is very interesting and definitely nothing like anything I’ve seen or used before. The main advantages of the product are that not only does it give you a valve maintenance feature by displaying a light if a fault is found within a valve, but it manages your valves to run at an equal number of milliamps. This means that each valve is working at an equal rate which in theory gives you optimum amp performance.

F50

Above : TubeSync fitted to a Mesa Boogie F-50

Oranges in the Tornado

Friday, June 3rd, 2011

Pics from Glory Days music in Joplin, MO USA. A reporter at CNN saw the orange tolex and took the pics.

We sincerely hope that the company can recover from this, our thoughts and best wishes go out to all.

IMG_6742

IMG_6743

Checkout the cymbal sliced into the door frame

IMG_6746

IMG_6748

IMG_6755

Orange Amps DIVO TubeSync and OV4 Explained

Thursday, April 21st, 2011

Orange Amps presents DIVO with TubeSync technology. DIVO helps increase the life of your tubes, protects against unexpected tube failure, and even allows for (4) different tube types to be installed in the same amp.

DIVO will come pre-installed on select Orange Rockerverb 100 MKII heads beginning Summer 2011. The OV4 stand-alone unit, also available in 2011, can be installed on almost any amp that has (4) power tube slots.

ov4_tubesync

Doug Doppler Demos Orange Amps Rockerverb 100 with DIVO Frankfurt Musikmesse 2011

Wednesday, April 13th, 2011

Doug Doppler Demos Orange Amps Rockerverb 100 with DIVO Musikmesse 2011

Orange Amps Rockerverb 100 with DIVO Musikmesse 2011 / Doug Doppler

Orange Amps Rockerverb 100 with DIVO Musikmesse 2011 / Doug Doppler

Orange Amps Launch TubeSync DIVO at NAMM 2011

Thursday, January 6th, 2011

For over forty years Orange amps has pushed back the boundaries of guitar amp technology and at NAMM 2011 the company is proud to announce a worldwide exclusive distribution agreement for DIVO TubeSync, a truly revolutionary new guitar amp technology. Here’s how Orange describes the technology:

TubeSync DIVO

The new DIVO technology automatically adjusts the bias of the output power tubes to ensure their full potential is realized. It monitors the amp’s performance and will isolate faulty tube failures, by running them at half power until the tubes can be changed. The DIVO system also increases the reliability of amplifiers by maintaining the optimum performance of the tubes by performing an ‘in circuit’ test every time the amplifier is powered up.

TubeSync-logo-500TubeSync DIVO technology opens up a whole new dimensions in tone options allowing for the first time ever the ability to mix and match tubes. You can experiment with an EL34, 6L6, 6550, KT77 or any other tube type all at the same time in the same amp. With DIVO the Tubes are automatically matched.

DIVO will extend the lifespan of your tubes and never again pay a tech to re-bias

Orange Logo Illustrator v9 BLKOrange amps will be offering this as option in their new Rockerverb 100 which will be “DIVO Ready.” For other Orange amps and most other brands Orange offer the DIVO Orange TubeSync OV4, a complete standalone unit.

KBO Dynamics TubeSync Technology

Friday, September 24th, 2010

Introduction

There is a certain quirkiness about the British psyche. On the one hand, the proportion of consumers in this country who actually bother thoroughly to read instruction manuals is undoubtedly very low. On the other, there was a Japanese survey, apparently, that found of all significant inventions going back over 200 years, 55% of them were British. Obviously, the Germans are more disciplined and better organised. The Americans are driven. The Japanese are still incredibly advanced technically, yet the British struggle to get the trains running on time. Maybe that’s the point: because we’re surrounded by chaos, we’ve had to become inventive.

The Americans make the best electric guitars but the British make the best amplification, goes the old adage. Doubtless, there are as many British luthiers as American amp manufacturers chorusing their disagreement, but as a general rule, this is probably true. And although if you look at all the great British amp makers – Hiwatt, Marshall, Sound City, Orange and the rest – they all have an Achilles Heel: the tubes. Ironic, really; amps that collectively have been responsible for the greatest sounds in contemporary music relying on components whose design hasn’t altered at all for decades. Enter TubeSync.

TubeSync_225

The engineering guys here at KBO Dynamics – inventors of TubeSync technology -are into power supply. Their background ranges from white goods to defence, and to be fair, making a washing machine go is hardly rock’n’roll. But when they turned their knowledgeable gaze towards tube amps, well, that’s different. For example, when a technician at Hiwatt builds a Custom tube amplifier, he and he alone will spend 20 hours soldering the components to stringent quality control guidelines: no production line or PCBs here. Yet, despite this labour of love, if the tubes fail, the amp won’t work. So when KBO Dynamics approached Hiwatt with a system that could monitor the tubes constantly when the amp is turned on, adjust the biases, forewarn if the tube was getting flaky and even switch pairs should one of the tubes fail completely, they pricked up their ears.

TubeSync

Musicians don’t shell out for a big, powerful expensive amp if they’re not gigging. That makes them either pro musicians or semi-pro at the very least. That also means that the public shell out to go and see them play. Therefore, neither party will be particularly chuffed if a tube goes in the middle of a performance. Yes, the pro musician probably carries a spare amp just in case, as most guitarists have a spare guitar in case they break a string, but it’s not ideal. TubeSync gives the musician peace of mind; simple. With TubeSync fitted in the amplifier, it’s a bit like having a dedicated amp tech working full time on that amp from the moment it’s turned on to the moment it’s turned off.

custom ampThe output from a traditional 100-watt valve amplifier comes from two pairs of EL34 tubes: matched 1 and 4, and 2 and 3. There are companies who sell ‘matched’ pairs of these tubes, as two identical tubes will tend to last longer than an unmatched pair. Normally, the EL34 will operate at 50Ma, although they can be rated higher, but the higher they are rated, the shorter their life. Best not to fiddle around too much, then. Better still, let TubeSync do what fiddling there needs to be done. The device, which is not an integral part of the amplifier, sits within the circuitry and ensures that the pairs remain matched throughout, and micro-adjusting the biases when necessary. Four LEDs on the facia plate – one for each tube – serve as a visual indicator of the state of each one. So the musician is given adequate warning if one of the tubes is getting flaky. In the unlikely event of one of the tubes letting go completely without warning, TubeSync will immediately switch out the affected pair; OK, the amp will be functioning at only half power, but at least it will be working. That’s peace of mind. Knowing that this technology is available but not using it would be a bit like driving really fast whilst wearing welding goggles. Don’t want to worry you or anything.

hayden Granted, having TubeSync installed in the amp is going to give peace of mind, but then we at KBO Dynamics haven’t just left it at that. Professionals in the music industry need to find out not only that there are certain strains on the tubes within the amp, but are there conditions within the live situation that perhaps put an amount of stress on the tubes above others. Handy that the techies can plug a laptop into TubeSync and get a readout, then. Handier still, we are working on an interface that when completed will allow the TubeSync-ed amp to hook up with either us or Hiwatt via the internet, and the amp’s performance can be monitored remotely in real time, even if the gig is in Australia. How formula 1 is that then? But then again, it isn’t, when you think about it; it’s more like professional progress. The Rolling Stones, for example, earn millions every time they tour – having seen them, they’re worth every penny, but that’s just one opinion – but they will never have toured in the past with amps loaded with TubeSync. Imagine the poor old amp techs frantically peering through the grilles of the back line checking for the dreaded EL34 red death glow while the band is laying it down for over a million fans on a beach in Brazil: now that’s stress.

We are talking with other amplifier manufacturers, but Hiwatt was a logical place to start: they are fiercely proud of their reputation for reliability, rightly so, and any technology that compliments that reputation is clearly going to be of interest to them. Both KBO Dynamics and Hiwatt feel that the incorporation of TubeSync technology genuinely adds value not just to the amplifier, but also to the whole amplification process. Tubes are still fairly reliable; with or without TubeSync, manufacturers wouldn’t build tube amps if they weren’t and we’re not in the business of scaremongering. However, the fact of the matter is that they are still the least reliable component part of the amp, and if you have experienced ‘sod’s law’, then you’ll know that if a tube is going to fail then it’ll pick the most inconvenient time to do so. Going back to the driving analogy, the odds of you needing the airbag in your car are reassuringly long. But try driving a car without one fitted, you genuinely do feel vulnerable.

Conclusion

In recent years, there has been an exponential rise in ‘extreme sports’ and the arrival of the adrenaline junkie, doubtless in response to an increasingly risk-averse society. The term “Nanny State” has been coined as a result. But let’s keep things in perspective; there’s a big difference in safety for safety’s sake and straightforward common sense. TubeSync technology has been designed to prolong the life of the tubes in the gigging musician’s amp – which is good – and also to alert them to the fact that the tube is approaching the end of its life – also good. We think that’s common sense, which is why we invented it.

TubeSync_500

TubeSync Service Points : Why Should You?

Friday, September 10th, 2010

TubeSync technology

TubeSync streamlines with the amp’s circuitry to constantly test and monitor the amp without altering the fundamental amplification process, tone or sound. It eliminates the need for bias current matching, increases tube life by micro-adjusting the bias on each tube, predicts tube failure and can, in the event of tube failure, even run the amp at half power, preventing catastrophic amp damage. ­­

The result is an amp unhampered by many of the problems associated with conventional tube amplification allowing musicians to enjoy classic tube sound quality without the frustrations.

These are just some of TubeSync’s unique features:

  • Eliminates the need for bias current matching of output tubes
  • Micro-adjusts the bias on each tube to ensure its full potential is realised
  • Assures reliability
  • Maintains optimum performance
  • Increases tube life
  • Reduces quiescent power consumption
  • Sets tubes at their optimum temperature as soon as you power up
  • Detects tube failure and prevents catastrophic damage to amp
  • Switches out faulty tubes and runs amps at half power until tube can be changed

A new industry standard

TubeSync technology has now been incorporated in new amp designs from some of the world’s most prominent amp manufacturers. Hiwatt, famed for their legendary reliability, was one of the first OEMs to recognise the potential of TubeSync for further enhancing the reliability and performance of their amps. KBO Dynamics continues to work with the industry’s biggest names to raise the bar in tube performance and reliability, creating a new industry standard in amp design and manufacture.

Introducing the Bias Engine

The Bias Engine is the hardware that encapsulates TubeSync’s unique technology. Fitting the Bias Engine is a straightforward procedure, with all necessary components supplied within the retrofit kit. It is stipulated that the Bias Engine is fitted by an accredited technician.

Bias engine retailThe Bias Engine is sold as a part of the TubeSync Professional Amp Upgrade Kit containing:

TubeSync Bias Engine Hardware

TubeSync hardware is wired straight into the amp’s circuitry. The Bias Engine is a very compact component that can be incorporated in both point-to-point and PCB wired amps.

Tube fault LED indicator harness and amp chassis LED plate

The Bias Engine is wired to 4 LED indicators that permanently illuminate when the tube is faulty and ‘flash’ when the tube needs to be replaced. The LEDs sit on the amp chassis, surrounded by the LED plate.

Wiring harness and mechanical fixings

The wiring harness, bundling all necessary wires and connectors, completes the kit along with a full set of mechanical fixings for securing the Bias Engine.

TubeSync Bias Runner software

Improving amplifier biasing methods, servicing and fault diagnostics

Interfacing with Bias Engine hardware, our Bias Runner software has been designed to allow OEMs and professional amp technicians to interrogate the status of an amplifier, alter bias settings, perform field diagnostics and configure the amp for best performance, further adding value to your services.Bias Runner_02

Bias Runner is easy to install, offering full fault diagnostics, enabling tube biasing with and without audio present, either collectively or as individual tubes. It is the perfect tool for warranty provision and servicing, providing a database of hardware serial numbers and storing amplifier parameter settings for full traceability.

Total service hours

Reads and displays the total number of hours the amplifier has been powered up. Optional reset facility available if required.

Total duration with audio

Reads and displays the total number of hours the amplifier has been driven with audio. Optional reset facility available if required.

Total hours idle

Reads and displays the total number of hours the amplifier has remained idle i.e. has not been driven with audio. Optional reset facility available if required.

Faulty tube log

Reads and displays the number of times a tube has been switched off due to a fault during the lifetime of the amplifier. A reset function is available for each individual tube.

Bias current (Audio present)

Enables the user to adjust tube current bias settings collectively or individually

Bias Current Idle (No Audio Present)

Enables the user to adjust tube current bias settings collectively or individually

Hardware and version status

Displays the serial number of the TubeSync module and the hardware version number

Serial number and settings database

Stores all serial numbers together with amplifier parameter settings in a   database for full traceability

Our commitment to you

We work closely with all of our partners to promote high standards and to support you in realising the full benefits of our truly innovative and impactful core technology and associated products.

As a TubeSync retailer or accredited technician you will receive:

Guaranteed product quality

All of our products are manufactured to the highest quality standards using state of the art assembly equipment. All components are ROSH compliant and uniquely identified for full batch traceability

A comprehensive solution

A complete package of hardware and software supports ease of use and easy configuration

Technical support

Our approach is founded on product and service quality. We offer our retail partners generous technical support to ensure that you are fully equipped for promoting TubeSync technology and advising your customers appropriately.

As an authorised retailer you will appoint a technician(s) who will receive training from our own technical team and who will be required to become certified as an accredited TubeSync technician before performing installations.

Warranty

All components come with a 12 month warranty which commences from the date of installation. Full warranty terms are available on request.