Posts Tagged ‘Technology’

Orange Amplification Announces DIVO VT1000 Valve Tester

Thursday, January 31st, 2013

Orange Amplification has released the DIVO  VT1000 Valve Tester, an automatic valve tester that performs a host of diagnostics on both preamp and power amp tubes. The unit has one octal and two nine pin valve sockets to fit pe-amp and EL34 valves. Once inserted, the user presses the start button and the tests are run.

Vt1000 valve tester

VT1000 Details:

Tests run:

  • Heater filament test: Short circuit
  • Heater filament test: Open circuit
  • Heater filament test: Tolerance check
  • Heater cathode insulation: Leakage
  • Heater cathode insulation: Short Circuit
  • Tests for heater current abnormalities
  • Amplification factor
  • Voltage gain
  • Power gain
  • Screen grid test
  • Mutual conductance test
  • Dual test for double triodes
  • Emission
  • Inter electrode leakage
  • Inter electrode short circuit
  • Flash-over (arc detection, high voltage breakdown)
  • Gas ionisation test

Compatible Valves:

  • EL34/6CA7
  • EL34L
  • 6L6
  • 6V6/6v6GTA
  • KT66
  • KT77
  • KT88
  • 6550
  • 5881
  • EL84/6BQ5
  • ECC81/12AT7
  • ECC82/12AU7
  • ECC83/12AX7
  • ECC99
  • 12BH7

Doug Doppler Demos Orange Amps Rockerverb 100 with DIVO Frankfurt Musikmesse 2011

Wednesday, April 13th, 2011

Doug Doppler Demos Orange Amps Rockerverb 100 with DIVO Musikmesse 2011

Orange Amps Rockerverb 100 with DIVO Musikmesse 2011 / Doug Doppler

Orange Amps Rockerverb 100 with DIVO Musikmesse 2011 / Doug Doppler

Tube Amp Testing For Professional Stage Performers – Engineering Tube Talk

Tuesday, February 22nd, 2011

A common requirement for tube amplifiers used for professional and stage purposes is that there should be a high percentage of confidence that one or more tubes will not fail during the performance. Tubes are often thought of in the same manner as light bulbs, in that they are most likely to fail catastrophically at switch on. This means that the moments just after the switch on point constitute the most stressful and potentially damaging periods in the life of the equipment.

In an attempt to guard against this possibility, it is common practice to do one of two things on a regular basis.

1/ regularly remove the tubes and have them commercially tested;

2/ replace the tubes with new stock on a regular basis.

These two methods may give the operator a degree of confidence but in fact, it can be shown that the faith placed in both methods is misplaced.

It is a known fact that removal of a tube from its socket results in a number of potentially damaging mechanical stresses on the metal to glass seals around the pins. Each insertion of an all glass tube will cause micro-cracking of the glass around the pin. This will invariably cause a small leakage of air into the valve, causing ‘gassing’ and eventually leading to its demise.

Removal for testing will also break the intimate contact between the holder and the tube contact pin, resulting in a poorer contact on re-insertion.

Many tube testers apply unreasonable electrical stresses to the tube internal electrodes and it is not uncommon for a known good valve to be damaged during the test. Tube testers can also give erroneous results depending on the way they perform the tests, possibly allowing faulty tubes to show ‘good’ and the good valves to be rejected as ‘bad’.

The second method of ‘blanket replacement’ with new stock on a regular basis can also lead to problems because if the failure distribution curve for tubes is analysed, it can be seen to follow the classic ‘bathtub’ failure curve. This inevitably means that an amplifier which is regularly ‘re-tubes’ will inevitably be considerably more likely to fail during the first hundred hours service than one which has been left untouched.

TubeSync overcomes these problems by performing an ‘in circuit’ test on the tubes every time the amplifier is powered up. The mutual conductance (gm) of the tube is measured by monitoring the cathode current of each valve whilst adjusting the grid bias in fixed steps. The results are tabulated and the new value is compared with previously stored values. A decision is then made on how far the tube has decayed in emission since the last test. Outputs from the device inform the user of the predicted remaining life of the tube.

TubeSync_350

The Scissor Sisters Choose Hiwatt, Hiwatt Choose TubeSync

Friday, October 8th, 2010

The extravagant disco pop group The Scissor Sisters have purchased a Hiwatt amp for recording and live performances. They have just been announced as support to Lady Gaga for the North American leg of her Monsters Ball tour and have a new single “Any Which Way” out now.

scissorsist

TubeSync_199

KBO Dynamics TubeSync Technology

Friday, September 24th, 2010

Introduction

There is a certain quirkiness about the British psyche. On the one hand, the proportion of consumers in this country who actually bother thoroughly to read instruction manuals is undoubtedly very low. On the other, there was a Japanese survey, apparently, that found of all significant inventions going back over 200 years, 55% of them were British. Obviously, the Germans are more disciplined and better organised. The Americans are driven. The Japanese are still incredibly advanced technically, yet the British struggle to get the trains running on time. Maybe that’s the point: because we’re surrounded by chaos, we’ve had to become inventive.

The Americans make the best electric guitars but the British make the best amplification, goes the old adage. Doubtless, there are as many British luthiers as American amp manufacturers chorusing their disagreement, but as a general rule, this is probably true. And although if you look at all the great British amp makers – Hiwatt, Marshall, Sound City, Orange and the rest – they all have an Achilles Heel: the tubes. Ironic, really; amps that collectively have been responsible for the greatest sounds in contemporary music relying on components whose design hasn’t altered at all for decades. Enter TubeSync.

TubeSync_225

The engineering guys here at KBO Dynamics – inventors of TubeSync technology -are into power supply. Their background ranges from white goods to defence, and to be fair, making a washing machine go is hardly rock’n’roll. But when they turned their knowledgeable gaze towards tube amps, well, that’s different. For example, when a technician at Hiwatt builds a Custom tube amplifier, he and he alone will spend 20 hours soldering the components to stringent quality control guidelines: no production line or PCBs here. Yet, despite this labour of love, if the tubes fail, the amp won’t work. So when KBO Dynamics approached Hiwatt with a system that could monitor the tubes constantly when the amp is turned on, adjust the biases, forewarn if the tube was getting flaky and even switch pairs should one of the tubes fail completely, they pricked up their ears.

TubeSync

Musicians don’t shell out for a big, powerful expensive amp if they’re not gigging. That makes them either pro musicians or semi-pro at the very least. That also means that the public shell out to go and see them play. Therefore, neither party will be particularly chuffed if a tube goes in the middle of a performance. Yes, the pro musician probably carries a spare amp just in case, as most guitarists have a spare guitar in case they break a string, but it’s not ideal. TubeSync gives the musician peace of mind; simple. With TubeSync fitted in the amplifier, it’s a bit like having a dedicated amp tech working full time on that amp from the moment it’s turned on to the moment it’s turned off.

custom ampThe output from a traditional 100-watt valve amplifier comes from two pairs of EL34 tubes: matched 1 and 4, and 2 and 3. There are companies who sell ‘matched’ pairs of these tubes, as two identical tubes will tend to last longer than an unmatched pair. Normally, the EL34 will operate at 50Ma, although they can be rated higher, but the higher they are rated, the shorter their life. Best not to fiddle around too much, then. Better still, let TubeSync do what fiddling there needs to be done. The device, which is not an integral part of the amplifier, sits within the circuitry and ensures that the pairs remain matched throughout, and micro-adjusting the biases when necessary. Four LEDs on the facia plate – one for each tube – serve as a visual indicator of the state of each one. So the musician is given adequate warning if one of the tubes is getting flaky. In the unlikely event of one of the tubes letting go completely without warning, TubeSync will immediately switch out the affected pair; OK, the amp will be functioning at only half power, but at least it will be working. That’s peace of mind. Knowing that this technology is available but not using it would be a bit like driving really fast whilst wearing welding goggles. Don’t want to worry you or anything.

hayden Granted, having TubeSync installed in the amp is going to give peace of mind, but then we at KBO Dynamics haven’t just left it at that. Professionals in the music industry need to find out not only that there are certain strains on the tubes within the amp, but are there conditions within the live situation that perhaps put an amount of stress on the tubes above others. Handy that the techies can plug a laptop into TubeSync and get a readout, then. Handier still, we are working on an interface that when completed will allow the TubeSync-ed amp to hook up with either us or Hiwatt via the internet, and the amp’s performance can be monitored remotely in real time, even if the gig is in Australia. How formula 1 is that then? But then again, it isn’t, when you think about it; it’s more like professional progress. The Rolling Stones, for example, earn millions every time they tour – having seen them, they’re worth every penny, but that’s just one opinion – but they will never have toured in the past with amps loaded with TubeSync. Imagine the poor old amp techs frantically peering through the grilles of the back line checking for the dreaded EL34 red death glow while the band is laying it down for over a million fans on a beach in Brazil: now that’s stress.

We are talking with other amplifier manufacturers, but Hiwatt was a logical place to start: they are fiercely proud of their reputation for reliability, rightly so, and any technology that compliments that reputation is clearly going to be of interest to them. Both KBO Dynamics and Hiwatt feel that the incorporation of TubeSync technology genuinely adds value not just to the amplifier, but also to the whole amplification process. Tubes are still fairly reliable; with or without TubeSync, manufacturers wouldn’t build tube amps if they weren’t and we’re not in the business of scaremongering. However, the fact of the matter is that they are still the least reliable component part of the amp, and if you have experienced ‘sod’s law’, then you’ll know that if a tube is going to fail then it’ll pick the most inconvenient time to do so. Going back to the driving analogy, the odds of you needing the airbag in your car are reassuringly long. But try driving a car without one fitted, you genuinely do feel vulnerable.

Conclusion

In recent years, there has been an exponential rise in ‘extreme sports’ and the arrival of the adrenaline junkie, doubtless in response to an increasingly risk-averse society. The term “Nanny State” has been coined as a result. But let’s keep things in perspective; there’s a big difference in safety for safety’s sake and straightforward common sense. TubeSync technology has been designed to prolong the life of the tubes in the gigging musician’s amp – which is good – and also to alert them to the fact that the tube is approaching the end of its life – also good. We think that’s common sense, which is why we invented it.

TubeSync_500

TubeSync UK Service Points Being Appointed

Friday, August 13th, 2010

We are offering select retailers and amp technicians the opportunity to become authorised suppliers of TubeSync technology and to take advantage of our new innovative amplifier technology.

  • Become a supplier of KBO Dynamics’ TubeSync Bias Engine
  • Generate revenue from hardware sales and fitting
  • Benefit from accreditation as a TubeSync technician
  • Add value to your offering with improved amplifier biasing methods, servicing and fault diagnostics, using TubeSync Bias Runner software
  • Get involved as TubeSync emerges in new amp designs from major amp manufacturers.

If you would like to be considered as TubeSync ‘Service Point’ then please email : info@tubesync.co.uk or telephone +44 (0) 1207 585846.

TubeSync_Service_Point

TubeSync For Valve / Tube Amps What am I ?

Friday, March 19th, 2010

About me:

I am a revolutionary new amp component, enhancing amp performance resulting in pure valve magic. My superior amp technology overcomes many of the problems associated with conventional tube amplification. With a little help from me there is no need for bias current matching, I can increase tube life and take your valves to their optimum temperature as soon as you power up. I can be easily integrated into any guitar valve amplifier. I take care of the detail, so you can concentrate on becoming a master of the strings . . . You can find a lot more about me on my main website www.tubesync.co.uk

The TubeSync Bias Engine

The TubeSync Bias Engine

Eliminates the need for bias current matching of output tubes

Increases manufacturing efficiencies

Micro-adjusts the bias on each tube to ensure its full potential is realised

Maintains optimum performance

Increases tube life

Assures reliability

Reduces quiescent power consumption

TubeSync

TubeSync

Never Hang Your Guitar Tubes / Valves Upside Down

Thursday, March 18th, 2010

Never hang your guitar tubes upside down as many horrible things may happen!!!

The heat from the electrodes will go directly to the base pins and cause problems with oxidization. The heat will also cause micro-cracks on the pins of the tube / valve, which could result in failures.

Don't_ hang_ your_tubesSo don’t do it !!…….

Thermionic Tubes & Tube Amplifier Operation

Friday, June 12th, 2009

Thermionic tubes

Thermionic tubes are very tolerant if their specified operating conditions are temporarily exceeded; unlike most semiconductors which tend to suffer from ‘catastrophic’ failure (defined as a failure mode which causes instantaneous and irreversible damage).Unlike semiconductors, tubes do however, ‘wear out’, which means that they have a finite operating life.

NN-M-EL34Operating them under unfavourable conditions or beyond the manufacturers working specification, usually results in a reduced lifespan, although this may not be audibly apparent in their operation. In audio applications, the majority of seriously damaging problems lie in the power output stages.

Introduction to Tube Amplifier Operation

The majority of amplifiers use at least two output tubes in a circuit configuration known as ‘Push-Pull’. Basically, this means that the audio signal is split into two halves by preceding circuits. Each of the two ‘Split’ signals now drives one output tube.

The signals then undergo power amplification by the output tubes and are re-combined by a special audio grade transformer which also drives the loudspeaker.  Please note that, although there are many different types of tube for various applications, the vast majority operate on the same basic principles.